[MAGIC-S7] Package Contents & Specifications
1. Package Contents
MAGIC-S7 provides the following tools and devices. The contents of the package may vary if optional items are purchased.
Take note:
*Cutter, tip and spindle belts easily wear out. Make sure to replace them regularly or as per maintenance schedule.
*All pictures shown are for illustration purpose only. Images may differ from the actual products.
*Be sure to use a safety mask and safety glasses to avoid injury during machine operation.
| Name | Picture | Qty | Usage |
| MAGIC-S7 |  |
1EA | Marking machine **※**Be sure to use a safety mask and safety goggles during machine operation for safety. |
| Power adapter (CP-01& CP-02) |
 |
1EA | Power supply ※Use a grounded outlet only. Do not plug the machine into an ungrounded outlet. |
| USB Cable (CP-11) |
 |
1EA | For connecting to PC |
| Program Installation USB |
 |
1EA | To install MagicEngrave software ※See program installation for further details. |
| User Manual |  |
1EA | Operating manual |
| T-wrench (2.5mm) (CP-T25) |
 |
1EA | For tightening/unscrewing the bolt. |
| L-wrench (1.5mm) (CP-L15) |
 |
1EA | For tightening/replacement of bolt. |
| Ruler (CP-24) |
 |
1EA | For measuring the material. |
| Tool fixing bolt (M5x6) |
 |
3EA | To fasten the spindle tool. |
| L-tool fixing bolt (M3x4) |
 |
3EA | To fasten the L-tool tip. |
| Diamond tip(4Ø) (T40-DA22) |
 |
1EA | For spindle: Tool used for engraving. |
| Diamond tip(3Ø) (T31-DA09) |
 |
1EA | For L-tool: Tool used for engraving the inside of a ring. |
| Bakelite plate (120x100x2t) |
 |
1EA | For calibrating the camera. |
| Multi-performance Clamp (CP-250) |
 |
1EA | To hold materials with different shapes in place. |
| Pin (CP-172) |
 |
6EA | To hold materials with irregular shapes in place. |
| Height adjustable clamp (CP-252) |
 |
1EA | To adjust the height of the clamp. |
| Finger chuck handle (CP-31) |
 |
2EA | To fasten the rotary clamp. |
| Flat finger chuck (CP-38) |
 |
3EA | For holding rings in place when engraving the inside or outside. |
| Round finger chuck (wide width) (CP-39) |
 |
3EA | For holding rings in place when engraving the inside or outside. |
| Finger Skin (CP-41) |
 |
1SET | For protecting finger chuck. |
| Finger Chuck Spanner (CP-21) |
 |
1EA | For tightening/unscrewing the finger chuck. |
Optional
*Purchased separately
| Name | Picture | Qty | Usage |
| Back Cover (CP-253) |
 |
1SET | Back Port Cover |
| Front cover |  |
1SET | To prevent inhaling of dusts and scattering of chips produced during engraving process. |
| Spacer block (CP-250S) |
 |
1SET | To adjust the height of the clamp. |
| Tailstock (CP-251) |
 |
1EA | Attached to the head: To protect tools and to cut at specific depth. |
| Pin clamp (CP-80) |
 |
1SET | To hold materials with different shapes in place. |
| Cutlery clamp (CP-83) |
 |
1SET | To firmly hold spoons in place. |
| Watch adapter (CP-84) |
 |
1SET | To firmly hold watch in place. |
| Bracelet adapter (CP-85) |
 |
1SET | To firmly hold bracelets in place. |
| Bar necklace adapter (CP-166) |
 |
1SET | Jig for holding materials with narrow width (about 2-3mm) in place. (Used for securing pendants, bar necklaces, etc.) |
| Curved tag adapter (CP-182) |
 |
1SET | Jig for holding curved materials in place. (Used for securing curved pendants, chain bracelets, etc.) |
| Round chuck finger (Narrow width) |
 |
3EA | For holding rings in place when engraving on the inside. |
※All pictures shown are for illustration purposes only. Images may differ from the actual products.
2. Specifications
| Operating voltage | AC 100~240V |
| Power consumption | 25W |
| Frequency | 50/60Hz |
| Dimensions | 402.5 mm(W) x 376.5 mm(D) x 352.5 mm(H) 15.8 in(W) x 14.8 in(D) x 13.9 in(H) |
| Max. engraving area | 140mm(X) x 100mm(Y) x 38.5mm(Z) 5.51 in(X) x 3.93 in(Y) x 1.51 in(Z) |
| Maximum material height | 60mm/ 2.4 in |
| Rotary operating range (Based on 2mm/ 0.08in) |
Cylinder outside diameter: MAX. 92mm (X) / MAX. 3.62 in (X) Cylinder inside diameter: MAX. 14mm (X) / MAX. 0.55 in (X) |
| Weight | 26kg / 57.32lb |
| Bluetooth | Bluetooth LE module/ Bluetooth 5.0 |
| Transfer speed | 80mm/sec (X,Y), 18mm/sec (Z) |
| Temperature | 15 – 40°C |
| Humidity | 10 - 90% |
| Purposes | Metal marking, Pen marking, Ring marking (inside), Ring marking (outside), etc. |