[MAGIC-L3] Installation

※Please follow the instructions below for proper installation of the machine, software and other devices.

※The software program requires Windows OS 7 or higher.

1. Machine

MAGIC™-L3 cannot operate alone as a desktop engraver. It cannot proceed to laser marking and cutting operation without the use of a computer and a software.

The machine should be connected to a personal computer for the machine to operate. The software provided along with the machine must be installed to the computer to run the program for laser marking and cutting.

How to install the machine

To start the machine, plug its power cable into a grounded outlet. ※See precautions for use for safety.
To connect the machine to the computer, plug in the USB cable on the back of the machine then on the computer’s USB port.

Power switch

Emergency Switch

※If the machine won’t turn on, check the emergency switch.

Back to the contents➜

2. Program

[System requirements]

-Supported devices: PC

-Operating system: Windows 10 or higher

-Processor: Intel® Pentium® CPU or higher

-Memory: 4GB or more

[How to install the software]

1. Insert the USB into your computer`s USB port. A notification will pop-up on your screen regarding installation. ※USB is included in the package.

2. Follow the instructions below to install the software.

3. Follow the steps in order until installation is complete.

4. In case program installation won’t automatically run upon inserting the USB into your computer, go to My Computer’s USB drive then run Install program.


1. Setup wizard.

2. Select installation folder.

3. Confirm installation.

4. The file is copied onto the hard disk.

5. USB driver setup wizard.

6. Check [I accept the agreement], then click [Next].

7. Check [Status: Ready to use], then click [Finish].

8. Click “Run MagicEngrave” button to complete program installation.

- Program Description

Once the installation is completed, the following icon will appear on your desktop. The description of the icon is as follows:


	As a design & marking software program, it features the following functions: marking design, marking option, Toolpath setting, transfer of Toolpath data.
	As a machine setting program, It features the following functions: Laser focus, Guide laser, Rotary origin, Manual calibration.

- Program serial number

After installation, the machine’s serial number is recognized and the stored set values in the server is automatically recalled and set.

-Click [OK] button to run set up automatically then the program automatically reconnects once setup is completed.

-Click [Skip] button to skip this process and the setting value will not be set automatically.

- Program password

Only administrators can use the program by using the program password.

Please make sure to change the default password.

The program default password is [0000].

Back to the contents➜

3. Driver

※The driver is automatically installed upon running program installation. If the driver is not properly installed, do manual installation.
※Be sure to connect the USB cable to the machine to run program installation.

Go to Device Manager, select USBLMCV2 file then select Update driver.

Follow the instructions below.

① Select Browse my computer for driver software.

② Click the Browse button.

③ Select the Driver folder from the installation CD file.

④ Add the Driver, then click the Next button.

⑤ Click “Close” button to complete program installation.

Back to the contents➜

4. Blower box

※Blower box set is sold separately.

※Be careful when using the hose clamp as its edges are sharp and may cause cuts.

※Using a dust collector or blower rated over 2A may cause machine malfunction. Do not connect or use products that exceed 2A.


Blower box (LMC-200)	1EA	Exhaust for dust & smoke.
Blower Hose(100Ø) (LMB-09-100)	2EA	Blower connection hose (2.5M)
Hose clamp(4inch) (LMB-10-4)	3EA	For connecting to blower and hose. ※ Please be careful of the cut surface of the hose clamp as it may cause injury.


Inlet	Connects to the duct hose to remove dust generated during processing.
Outlet	Connects to the duct hose to discharge dust after collection.
Power Switch	Turns the blower ON/OFF.
Power Port	Connects the blower to the power source.

How to install the blower box

Back to the contents➜

5. Auxiliary power device setup

※Auxiliary power device set is sold separately.
※Auxiliary power device is required when using the blower.

Auxiliary Power Device		1EA	Auxiliary Power Device must be used if the external blowers or dust collectors have more than 2 Ampere.
Power cable		2EA	Supplies power and connects to the machine.

The auxiliary power device must be used if the external blower has more than 2 Ampere. Failure to use this device will result in machine failure.

Connect the auxiliary power device to the laser machine. (See picture below for reference.)

Back to the contents➜

6. IO Port in/output

※External IO port input to the machine is at 5V, use 5mA or less.

MAGIC™-L3 has a function that outputs machine operational status via IO port and receives external signals through the IO port to control operation.

To operate an external device by linking to L3 status signal output, connect the signal line to the OUT port that outputs the status to operate the external device. To activate L3 by external-device status signal, connect the external-device signal line to the IN port linked to L3 operation. The function of each IO port is as follows:

Power	+5V Power	+5V power necessary to connect external devices
Output	Laser Start	Auto laser engraving start upon +5V (High) signal output from an external device
Output	Laser Stop	Immediate laser engraving stop upon +5V (High) signal output from an external device
Input	Laser ON Signal	+5V (High) signal input to an external device upon laser engraving start.
Input	Laser OFF Signal	+5V (High) signal input to an external device upon laser engraving end.
Input	Blower On/Off Signal	When the blower is ON, +5V (High) input to an external device; and, if OFF, GND (Low).
Power	GND	GND power necessary for external-device connection.

**OUT: Signal received from external devices
**IN: Signal received by the machine

Back to the contents➜

7. External device

※Blower Power Inlet: 110~220V/2A

※Auxiliary Power Device must be used if the external blower has more than 2 Ampere.

1. Connect the power to the back of the machine.

2. Click [OTHER] in [Setup Machine].


Auto	If [Auto] checkbox is selected, the auto on/off function of the externa device is enabled during machine operation. If [Auto] checkbox is not selected, the auto control function of the external device is disabled.
Power Off Delay	The external device automatically turns OFF after a delay.

Back to the contents➜

8. Back cover

※Back cover set is sold separately.

Back Cover (CP-253)	1EA	Back Port Cover
Square Magnet	2EA	To secure the back cover.
Bolt (M3x8mm)	3EA	To secure the square magnet.

Assemble the back cover then attach it to the back side of the machine.

Insert the bolt into the square magnet then screw it into the machine.

Attach the back cover. The back cover is secured by the square magnets.

Back to the contents➜

9. Operation of the marking machine

MAGIC™-L3 performs self-diagnosis upon turning ON. During self-diagnosis, the machine checks the following in order:

Self-diagnose Procedures

If a certain axis is detected by the sensor, it moves away from the detected area.
Checks the cover sensor.
Checks the z-axis sensor and returns to the origin point.
Returns to the origin point.
Confirmation sound and standby

If no problem is found, it goes into standby mode with a confirmation sound.

Marking Procedures

1. Turn on the marking machine.

※ If the machine does not turn on, check the emergency switch.

2. Run the program to connect it to the machine.
※When the machine is connected to the program, the machine’s cover automatically opens upon initialization.