Contents

• 1. Machine
• 2. Clamp
• 3. Keypad
• 4. Menu
• 5. Display
• 6. Status indicator
• 7. Switching tools

1. Machine

Protect your hands, wrists and fingers.
Do not put any of your body parts inside the machine or anywhere near the head during operation.

Back to the contents➜

2. Clamp

1) Flatbed Clamp

Place the material on the flatbed then secure it by using the clamps provided (see clamps below). The clamps are used to secure the material to the flatbed so that the material stays in place during engraving or cutting process. The number of clamps to be used may vary depending on the size and/or shape of the material.

※See picture for reference.

L-wrench(4mm) (CP-L40)		1EA	For tightening/unscrewing the bolt.
Push clamp		2EA	To hold materials in place.
Push clamp		2EA	To hold materials in place.
Knob (M5x12mm)		2EA	To secure the clamp set.
Knob (M5x25mm)		2EA	To secure the clamp set.
Knob (M5x30mm)		2EA	To secure the clamp set.
Knob cap		2EA	Cap for knob: Used with **M5x25mm knob.**
Bolt (M5x10mm)		5EA	To secure the clamp set.
Bolt (M5x18mm)		5EA	To secure the clamp set.

How to secure the material with press clamps

For thin material:
Both press and push clamps can be used to secure thin materials. Use the knobs to attach the clamps to the flatbed. Screw the knobs down to the flatbed to secure the material in place. Take note that the position of the clamps and the number of clamps to be used may depend on the size and shape of the material. It may also depend on user’s preference.

Press clamp with knob	Push clamp with knob

For thick material:

1. Assemble the press clamp. Insert the M5x25mm knob into the hole of the press clamp then screw the cap.

2. Place the material on the clamp.

3. Place the assembled press clamp on top of the material (in a horizontal position). The clamp must be placed on the same level as the material surface.

4. Attach the press clamp to the flatbed. Insert the M5x30mm knob into the press clamp then screw the knob down to secure the material to the flatbed.

5. Secure the sides of the material. Use two or more clamps to secure the material. Be sure to screw the knobs down to the flatbed so the material stays in place.

Height Adjustable Clamp

Height adjustable clamp is used to adjust the height of your material.

Height adjustable clamp (CP-252)

1EA

To adjust the height of the clamp.

1. Turn the Height Adjustable clamp clamping knob counterclockwise to detach the Multipurpose Clamp.

2. Turn the clamping knob counterclockwise to detach the height adjustable clamp.

3. Attach the multipurpose clamp then fasten it by turning the clamping knob clockwise.

L-Type Clamp

※Optional device; sold separately
Used to secure locks to the flatbed (work area).

How to install the jig

1. Screw the M5 bolts to the flatbed with an L-wrench.

2. Match the size of the lock (material) to the clamp. To adjust, reposition the upper part then screw the bolts to the flatbed.

2) Multipurpose Clamp

The package includes a multifunctional clamp that is easily assembled, disassembled and transformed into 3 different types of clamps. It can be adjusted according to the height of the material, and can be expanded according to the material’s thickness, size, and shape. This single clamp alone makes engraving on various materials possible without the use of any additional clamps.

How to secure the material in place

Use the clamping knob to secure your material in place. To loosen or widen the clamp, turn the clamping knob counterclockwise; to fasten it, turn the knob clockwise.

Marks may be left on the material if fastened tightly.

How to position the material

Use the vertical ruler bar as an alignment guide to help you position and align your material to the clamp with ease and accuracy. Properly place your material on the clamp then check the alignment.

How to secure the material with irregular shape in place

Use the clamping pins to firmly hold materials with irregular shapes in place. To secure the clamping pins to the clamp, simply insert the pins into the pin holes then fasten them.

How to adjust the height of the clamp

Below are instructions on how to adjust the height of the clamp according to the thickness of the material.

1. Turn the clamp over (to the back) then screw the bolts (M4x20mm). ※Use a 3mm L-wrench to screw the bolts.

2. Turn the clamp over (to the front) then pull out the clamp base.

3. Remove the clamping pins then secure the material to the V groove of clamp without clamp base. (See picture below for reference).

Height Adjustable Clamp

Height adjustable clamp is used to adjust the height of your material.

Height adjustable clamp (CP-252)

1EA

To adjust the height of the clamp.

1. Turn the Height Adjustable clamp clamping knob counterclockwise to detach the Multipurpose Clamp.

2. Turn the clamping knob counterclockwise to detach the height adjustable clamp.

3. Attach the multipurpose clamp then fasten it by turning the clamping knob clockwise.

How to adjust the height of the clamp

※Optional device; sold separately
Below are instructions on how to adjust the height of the clamp according to the thickness of the material.

Spacer block (CP-250S)

1EA

To adjust the height of the clamp.

1. Turn the clamping knob counterclockwise to detach the clamp.

2. Turn the clamp over (to the back) then screw the bolts (M4x20mm). ※Use a 3mm L-wrench to screw the bolts.

3. Once the bolts are removed, turn the clamp over (to the front) then pull out the clamp base. Then, reassemble the spacer block to pin.

※ After secure the spacer block, then secure the material to the V groove of clamp.

4. Screw the spacer block fixing bolt (M4x20mm). ※Use a 3mm L-wrench to unscrew the bolts.

5. Secure the base clamp by attaching it to the pins.

6. Turn the clamp over (to the back) then unscrew the bolts (M4x40mm).
   ※Use a 3mm L-wrench to unscrew the bolts.

※ To assemble or reassemble the spacer block, use the appropriate bolts. Be sure to use and secure the spacer block using the correct type of bolts.

Spacer block fixing bolt- M4x20mm	Clamp base fixing bolt- M4x40mm

Optional items for Multipurpose Clamp

1. Pin clamp

※Optional device; sold separately

Pin clamp (CP-80)		1SET	To hold materials with different shapes in place.
Pin (CP-172)		5EA	To hold materials with irregular shapes in place.
Wrench bolt (M4x6)		5EA	To fasten the clamp.
L-wrench(3mm) (CP-L30)		1EA	For tightening/unscrewing the bolt.

2. Cutlery clamp

※Optional device; sold separately

Cutlery clamp (CP-83)

1SET

To firmly hold spoons in place.

3. Watch adapter

※Optional device; sold separately

Watch adapter (CP-84)		1SET	To firmly hold watch in place.
Wrench bolt		5EA	To fasten the adapter.
L-wrench(3mm) (CP-L30)		1EA	For tightening/unscrewing the bolt.

4. Bracelet adapter

※Optional device; sold separately

Bracelet adapter (CP-85)		1SET	To firmly hold bracelets in place.
Pin		4EA	To secure the adapter.

5. Bar necklace adapter

※Optional device; sold separately

Bar necklace adapter (CP-166)		1SET	Jig for holding materials with narrow width  (about 2-3mm) in place. (Used for securing pendants, bar necklaces, etc.)
Pin		4EA	To secure the adapter.

*Materials like bar necklaces or pendants may come off easily when attaching to the jig. 
Press the material with your finger to secure it to the jig and be sure to not let your finger get caught while pressing. 

6. Curved tag adapter

※Optional device; sold separately

Curved tag adapter (CP-182)		1SET	Jig for holding curved materials in place. (Used for securing curved pendants, chain bracelets, etc.)
Pin		4EA	To secure the adapter.

3. Keypad

Display		Status display
Operation Buttons		Activate the operations intended to perform
		Direction Key (X,Y/Z)	Engraving area adjustment (X) Moves X axis (Y)(Z) Moves Y/Z axis ※Axis movement can be changed by using the operation buttons.
		Vacuum ON/OFF	Chip collector power button • Automatic control: The device starts automatically once the engraving operation begins and stops automatically once the engraving operation is completed. • Manual operation: Automatic control is deactivated if the device is manually switched on. Once the engraving operation is completed, the device should be manually turned off. ※ We strictly advise our users to use the Chip collector during engraving operation for safety. The Chip collector prevents exposure form harmful inhalable particles and debris like metal chips and dusts which may cause eye injury if they get stuck in the eye or respiratory problems if inhaled.
		Start	Start marking button • Start marking: Long-press (for 2 seconds) the [Start] button to start marking. • Repeat marking: Press the [Start] button to finish marking, then double-press (tap twice) the [Start] button to repeat marking. • Menu: Press OK when using the menu.
		Menu	Enter the menu mode
		Stop	Stops/cancels marking

Back to the contents➜

4. Menu

To enter Menu mode, press  button. Select a menu item using the  and  buttons then press button to enter the menu item.

Back to the contents➜

5. Display

The display shows the status, functions, mode, and check messages. Icons are displayed differently depending on the selected function. The four buttons at the bottom represent different functions and each function vary depending on the selected mode.

1) Standby-Flat

	Status
	Bluetooth	Icon appears when Bluetooth is activated
	Auto Zref on Repeat	: No measurement : Height measurement only : Height measurement + area check
	Chip collector Power	Chip collector ON/OFF: Icon does not appear when OFF
	Focus Pointer	Laser pointer ON/OFF
XY:#1-C	X-Y Origin	X-Y origin •#1: Clamp No. (1-5) •C: Origin No. (C: Center; origin No.: 1-8)

	Mode
	Left-top origin	Moves the tool to the position saved in the “Left-top” button and sets the position as origin
	Center origin	Moves the tool to the position saved in the “Center” button and sets the position as origin
	Tool change	Switches to tool change mode
	Auto focus	Activates camera auto focus position • Auto moves to view position after height measurement • Refreshes the camera display at MagicEngrave. ※Variety of features available for use once MagicEngrave software is enabled.

2) Move Mode

Press one of the buttons in the [STANDBY] mode to activate [MOVE].

	Mode
	Standby Mode	• Switches to the STANDBY mode  • Switches automatically to [STANDBY] mode if not in use for 10 seconds. Press any buttons to activate [MOVE] mode.
	Save Origin	Saves the current position as the XY origin *Short-press: Temporary save *Long-press: Permanent save Y-axis movement mode: Save XY Origin Z-axis movement mode: Save Z Origin
	Laser Pointer	Turns ON/OFF the laser pointer
	UP-DOWN Button Settings	The mode changes in sequence (Y-axis → Z-axis → Y-axis) in a loop whenever the button is clicked.

3) Engraving mode

	Engraving Speed Control	Reduces engraving speed by 1mm/s whenever the button is pressed.
		Increases engraving speed by 1mm/s whenever the button is pressed.

4) Pause

	Mode
	Return back to Previous position	Returns back to the previous position and resumes engraving.
	Tool Change	Switches to tool change mode
	Resume	Resumes engraving.

Back to the contents➜

6. Status Indicator

The status indicator is placed at the bottom left side and bottom right side of the machine. It is used to indicate the status of the device.

The machine displays flashing or blinking lights to show its current status. The lights displayed indicate the following status: 

Status	Blinking Interval
Waiting
Engraving
Operating
Notification
Error

Press button (for 2 seconds) to enter menu mode.

Select [5. Adjust Brightness] then press  button.

Select [1. Status LED] then press  button.

Adjust the brightness using the (Direction X) buttons.

Back to the contents➜

7. Switching Tools

Do not let any of your body parts or any foreign objects get caught in the machine during operation. 

The tools of the machine are sharp, and may cause serious physical injury.

Please wear safety glasses during engraving process for safety. 

Debris like metal chips and dusts may cause serious eye injury if they get stuck in the eye.

• Spindle

Name	Picture	Quantity	Usage
T-wrench (2mm)		1EA	Tool for tightening/unscrewing of bolt.

As shown below, insert the 2mm wrench into the fixing bolt. Turn the wrench to the left to unscrew bolt. To prevent the tool from falling to the floor, grab tool with your hand then pull it out. Once the tool is removed, replace it with a new tool then secure it using a wrench for tightening bolts. ※See package contents

When unscrewing the tool fixing bolt, hold the tool with your hand while unscrewing to avoid the bolt from dropping on the floor.

Back to the contents➜

S4 Main➜